Dodaj u košaricu za još 500 kuna i izbjegni trošak dostave.
Na sve narudžbe iznad 500 kuna nemaš troškove dostave. Iskoristi priliku!

Senzor pokreta LSM303D, 6DoF Motion Sensor Breakout

Osnovne značajke
  • Šifra proizvoda: 8208000604
89,00 kn u dućanu
84,55 kn
Jamstvo: 12 mjeseci Dostava: 5 radnih dana
Jednokratno plaćanje:
Internet bankarstvo (virman)
Pouzeće (prilikom preuzimanja)
American Express, Maestro, MasterCard, Visa
Obročno plaćanje:
MasterCard 2-12 rate
Visa Premium 2-10 rata
DOSTUPNOST PO POSLOVNICAMA:
ZAGREB - VUKOVARSKA, WEB SHOP
  • Adafruit

    ABOUT US Adafruit was founded in 2005 by MIT hacker & engineer, Limor "Ladyada" Fried. Her goal was to create the best place online for learning electronics and making the best designed products for makers of all ages and skill levels. Adafruit has grown to over 100+ employees in the heart of NYC with a 50,000+ sq ft. factory. Adafruit has expanded offerings to include tools, equipment, and electronics that Limor personally selects, tests, and approves before going in to the Adafruit store. Adafruit is a 100% woman owned company.

    » PREGLED SVIH ADAFRUIT PROIZVODA

  • OPIS

    This 6 Degrees of Freedom Motion Sensor Breakout can detect acceleration in three axes - X, Y, and Z - as well as three axes of magnetic heading.
    It's ideal for building into robots, rockets, and rovers, or anywhere else where you want to measure motion accurately.
    It's compatible with Raspberry Pi or Arduino.

    The LSM303D 6DoF Breakout has an I2C interface and is 3.3V or 5V compatible.
    Like our other Pimoroni breakouts, we've designed it so that you can solder a piece of right-angle header
    onto it and then pop it straight onto the bottom left 5 pins on your Raspberry Pi's GPIO header (pins 1, 3, 5, 6, 9).

    It's also compatible with our fancy new Breakout Garden, where using breakouts
    is as easy just popping it into one of the six slots and starting to grow your project, create, and code.

    Features

    LSM303D 6DoF Motion Sensor
    ±2/±4/±8/±12 gauss magnetic scale
    ±2/±4/±6/±8/±16 g linear acceleration
    16 bit data output
    3.3V or 5V compatible
    I2C interface, with address select via ADDR cuttable trace (0x1D or 0x1E)
    Reverse polarity protection
    Raspberry Pi-compatible pinout (pins 1, 3, 5, 7, 9)
    Compatible with Raspberry Pi 3B+, 3, 2, B+, A+, Zero, and Zero W
    Python library
    Datasheet

    Kit includes

    LSM303D 6DoF Motion Sensor Breakout
    1x5 male header
    1x5 female right angle header

    Software

    We've put together a Python library that you can use to read data from your LSM303D 6DoF Breakout,
    and an easy one-line installer to install everything.

    Our software does not support Raspbian Wheezy.

    Notes

    The trace between the solder pads (marked ADDR) can be cut (carefully with a craft knife)
    to change the I2C address from the default of 0x1D to 0x1E, meaning that you can use up
    to two sensors on the same Raspberry Pi or Arduino.
    If cut, the pads can be bridged again by soldering to reset the address to 0x1D.