Arduino WI-FI shield A000058

Osnovne značajke
  • Šifra proizvoda: 8090229125
735,00 kn u dućanu
712,95 kn
Jamstvo: 12 mjeseci Isporučivo: 1 dan
Jednokratno plaćanje:
Internet bankarstvo (virman)
American Express, MasterCard, VISA, Maestro
Obročno plaćanje:
American Express 2-10 rata
DOSTUPNOST PO POSLOVNICAMA:
ZAGREB - VUKOVARSKA, SPLIT, RIJEKA, OSIJEK, ZAGREB - ARENA, ZADAR, ŠIBENIK, PULA, WEB SHOP
  • Arduino

    Arduino je talijanska kompanija specijalizirana za elektroniku. Osnovana je 2005. godine u Italiji. Arduino je softverska i hardverska kompanija koja je posvećena kit elektronici. Također nudi i vlastiti programski jezik i veliku bazu znanja i uputa za izgradnju elektroničkih sustava. Chipoteka vam nudi veliki izbor kit elektronike marke Arduino koja je idealna za hobiste i učenje elektronike i elektroničkih programa.

  • OPIS

    Overview

    The Arduino WiFi Shield connects your Arduino to the internet wirelessly.
    Connect it to your wireless network by following a few simple instructions to start controlling your world through the internet.
    As always with Arduino, every element of the platform – hardware, software and documentation – is freely available and open-source.
    This means you can learn exactly how it's made and use its design as the starting point for your own circuits.

    Requires an Arduino board (not included)
    Operating voltage 5V (supplied from the Arduino Board)
    Connection via: 802.11b/g networks
    Encryption types: WEP and WPA2 Personal
    Connection with Arduino on SPI port
    on-board micro SD slot
    ICSP headers
    FTDI connection for serial debugging of WiFi shield
    Mini-USB for updating WiFi shield firmware

    Description

    The Arduino WiFi Shield allows an Arduino board to connect to the internet using the 802.11 wireless specification (WiFi).
    It is based on the HDG104 Wireless LAN 802.11b/g System in-Package. An Atmega 32UC3 provides a network (IP) stack capable of both TCP and UDP.
    Use the WiFI library to write sketches which connect to the internet using the shield. The WiFI shield connects to an
    Arduino board using long wire-wrap headers which extend through the shield.
    This keeps the pin layout intact and allows another shield to be stacked on top.

    The WiFi Shield can connect to wireless networks which operate according to the 802.11b and 802.11g specifications.

    There is an onboard micro-SD card slot, which can be used to store files for serving over the network.
    It is compatible with the Arduino Uno and Mega. The onboard microSD card reader is accessible through the SD Library.
    When working with this library, SS is on Pin 4.

    Arduino communicates with both the Wifi shield's processor and SD card using the SPI bus (through the ICSP header).
    This is on digital pins 11, 12, and 13 on the Uno and pins 50, 51, and 52 on the Mega.
    On both boards, pin 10 is used to select the HDG104 and pin 4 for the SD card.
    These pins cannot be used for general I/O. On the Mega, the hardware SS pin, 53,
    is not used to select either the HDG104 or the SD card, but it must be kept as an output or the SPI interface won't work.

    Digital pin 7 is used as a handshake pin between the WiFi shield and the Arduino, and should not be used.

    Note that because the HDG104 and SD card share the SPI bus, only one can be active at a time.
    If you are using both peripherals in your program, this should be taken care of by the corresponding libraries.
    If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it.
    To do this with the SD card, set pin 4 as an output and write a high to it.
    For the HDG104, set digital pin 10 as a high output.

    The shield can connect to encrypted networks that use either WPA2 Personal or WEP encryption.
    It can also connect to open networks.

    A network must broadcast its SSID for the shield to be able to connect.